深圳市源泉工程塑胶原料有限公司

牌号 P3010           厂家(产地) 德国巴斯夫 
用途级别 耐高温 耐化学品 玻璃纤维增强阻燃级      

Ultrason® P 3010 NAT | BASF | PPSU 物性表

Unreinforced, higher viscosity injection moulding grade, flameretardent and with improved chemical resistance.
Abbreviated designation according to ISO 1043-1: PPSU

典型数据

加工方法

注塑, 薄膜挤出成型, 异型材挤出成型, 片材挤出成型, 其它挤出成型, 吹塑, 热成型

供货形式

粒料

地区供应

北美, 欧洲, 亚太, 中南美洲, 中东/非洲

top

Processing Texts

注塑成型

PREPROCESSING
Pre/Post-processing, max. allowed water content: .02 %
Pre/Post-processing, Pre-drying, Temperature: 140 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 350 - 390 °C
injection molding, Melt temperature, recommended: 370 °C
injection molding, Mold temperature, range: 140 - 180 °C
injection molding, Mold temperature, recommended: 160 °C

Pretreatment
Drying temper ature: 130 - 150°C
Drying time: minimum 4h
recommended dryer: vaccum or dry air dryer
maximum moisture: 0,02 - 0,05%

Ultrason® can be injection molded by any type of machinery on the market, provided that the plasticizing unit and the mold temperature control system have been configured appropriately. The machinery manufacturer must be consulted if any doubts exist on the ability of various parts to withstand the high temperatures required (e.g. barrel, barrel he ad, bolted connections, etc.)

Long residence time in combination with high temperatures should be avoided e.g. by pump out material at regular intervals.
During extended interruptions, the barrel temperature should be lowered to about 250-280°C.

It has been found out that heating to the requested processing temperature and shutting down or lowering the temperature is best carried out in two steps.
First, the barrel temperatures are set at the lower processing temperat ure range for the particular thermoplastic (340 - 350 °C). As soon as these temperatures have reached a steady state, the material in the barrel is pumped out. Second, the barrel temperature can be set to the required processing temperature or the heaters can be shut down.

    德国巴斯夫（BASF）在热可塑性工程塑料“ULTRASONE”系列中追加了新产品Polyphenyl Sulfone（PPSU）“ULTRASONE P”。ULTRASONE P的特点是：兼具该系列中Polyether Sulfone（PESU）“ULTRASONE E”的高熔融温度和Poly Sulfone（PSU）“ULTRASONE S”的低吸水性，而且耐药性也很出色。目前，已开始供应“ULTRASONE P3010”的透明产品样品，今后还将依次上市白色和黑色的P3010。 

原来的高性能非结晶塑料存在接口部位受到冲击应力时容易损坏的缺点。该公司进行的夏氏冲击试验结果表明，ULTRASONE P的耐冲击性约为普通非结晶塑料的10倍。因此可在需要较强耐冲击性的配管接头和阀门上使用。 

可承受2000次的高温蒸汽循环，可用高温清洗、杀菌。另外，发生火灾时也不易排放有害物质，因此该公司希望能够在飞机的座套、灯罩、换气阀及行李箱上使用该产品。（



        东莞市鼎鑫塑化原料有限公司长期代理销售德国巴斯夫系列高品质工程塑料产品，以下产品长期现货供应，价格优惠，质量百分之百保证！